Whole numbers, signed numbers, and the order of operations

Your progress is saved on this device only. Log in to keep a training record.

Program in development. FLY8MA is not yet an FAA-certificated Part 147 school.

Lesson text: Whole numbers, signed numbers, and the order of operations

The reading from the lesson above, as plain text. The video, the practice and the quiz are in the lesson itself.

The oil sits at minus 14 inches, and draining it is a minus too. Is a minus times a minus a plus or a minus?

This lesson reviews basic arithmetic, using an oil change on N172BL as the example. Watch the video first, then work through the reading and the practice.

By the end of this lesson you will be able to:

  • add, subtract, multiply and divide whole numbers.
  • add, subtract, multiply and divide numbers below zero.
  • carry a minus sign from an FAA data sheet through a calculation.
  • work the steps of a calculation in the correct order.

The problem

N172BL is the Cessna 172 that Big Lake Air Service rents out, and you are the mechanic working on it. The shop writes the jobs to be done on an airplane on a work order: a written list, one job to a line. This module follows one work order of eight lines on N172BL, and each lesson works the numbers for one line. This lesson is line 1. The airplane is in for an oil change, so the oil has been drained. The FAA's sheet for this airplane lists the oil at minus 14 inches. Taking something off the airplane is also a minus. So working out what the missing oil changes has a minus times a minus in it. Is the answer a plus or a minus?

This lesson gives you the arithmetic to answer that: adding, subtracting, multiplying and dividing; numbers below zero; and which step of a calculation to work first. You may use a calculator for the multiplying and dividing in this lesson.

Whole numbers and place value

Whole numbers are the numbers 0, 1, 2, 3, 4, 5, and so on (FAA General Handbook, Chapter 3, page 3-1). They are the numbers you count with.

Figure 1. Place values of three whole numbers. Each digit sits in its own column: ones, tens, hundreds, thousands, ten thousands. FAA-H-8083-30B, Figure 3-1

A digit is one of the ten figures 0 to 9 that numbers are written with. The place value is the value of the position of each digit within the whole number. In the number 512, the 5 is in the hundreds column, the 1 is in the tens column, and the 2 is in the ones column. So the 5 stands for 500, the 1 for 10 and the 2 for 2. Figure 1 sets out three numbers this way (FAA General Handbook, Chapter 3, page 3-2).

Addition puts numbers together. The answer to an addition is called the sum. To add several whole numbers by hand, line them up in columns by place value, ones under ones and tens under tens, and then add. The handbook adds 4,314, 122, 93,132 and 10:

4,314 + 122 + 93,132 + 10 = 97,578

Subtraction takes one number from another. The answer to a subtraction is called the difference. The handbook takes 3,461 from 97,564:

97,564 − 3,461 = 94,103

Multiplying and dividing

Multiplication is repeated addition. The sign × means "multiplied by": 4 × 3 is the same as 4 + 4 + 4. The answer to a multiplication is called the product (FAA General Handbook, Chapter 3, page 3-1).

The handbook's example: the supply room holds 35 cartons, and each carton holds 18 filters. How many filters is that?

35 × 18 = 630 filters

By hand, work it in two parts and add them: 35 × 10 = 350 and 35 × 8 = 280. Then 350 + 280 = 630. The 1 in 18 is in the tens column, so it stands for 10.

Division finds how many times one number is contained in another. The sign ÷ means "divided by". The number you divide by is the divisor. The number being divided is the dividend. The answer is the quotient, and any amount left over is the remainder. In 6 ÷ 2 = 3, the divisor is 2, the dividend is 6 and the quotient is 3.

The handbook's example: 218 bolts are to be divided between 7 aircraft. Seven goes into 218 thirty-one times, because 7 × 31 = 217. That leaves 218 − 217 = 1.

218 ÷ 7 = 31, remainder 1

Each aircraft gets 31 bolts and one bolt is left over (FAA General Handbook, Chapter 3, page 3-2). A calculator shows this answer as 31.142857. A number with a point in it, such as 31.142857 or 11.3, has a part smaller than one after the point. Lesson 2 teaches these numbers; in this lesson a calculator handles them. The 31 is the quotient. The digits after the point are not the remainder; to find the remainder, multiply back and subtract, as above.

Numbers below zero

A positive number is a number that is greater than zero. A negative number is a number that is less than zero. A negative number is written with a minus sign in front of it, such as −5. A positive number is written with a plus sign, such as +5, or with no sign at all. A signed number is a number that carries a plus or a minus sign: a positive or a negative number (FAA General Handbook, Chapter 3, page 3-11).

Figure 2 shows signed numbers on a scale: a line marked with numbers in order. Zero is in the middle. The further left a number is, the smaller it is: −5 is less than −1.

Figure 2. A scale of signed numbers. Zero is in the middle; the numbers to its left are negative and the numbers to its right are positive. FAA-H-8083-30B, Figure 3-8

An integer is a whole number, its negative, or zero: ... −2, −1, 0, 1, 2 ... (This definition is plain mathematics; it is not from an FAA page.) One sentence on that handbook page is a misprint: "Signed numbers are also called integers." They are not the same thing. The number −14 is an integer and a signed number. The number −11.3 is a signed number, but it is not an integer, because it has a part after the point. Lesson 2 covers numbers like 11.3.

Adding. Two positive numbers add to a positive number. Two negative numbers add to a negative number. A positive and a negative number can add to either, depending on which is larger. The handbook's picture is a debt. If you owe $100, your account is at −100. Pay in $45 and you still owe $55:

−100 + 45 = −55

The handbook's second example is an aircraft. It weighs 2,000 pounds. A radio rack of 3 pounds and a radio of 10 pounds are taken out. The handbook's rule: everything removed from an aircraft is given a minus sign, and everything added is given a plus sign.

2,000 + (−3) + (−10) = 1,987 pounds

Subtracting. To subtract a signed number, change the subtraction to an addition and change the sign of the second number. Then add (FAA General Handbook, Chapter 3, page 3-11). The handbook's example: the temperature on the ground is 6 degrees below zero, written −6°. (A degree is one step on a thermometer's scale.) Higher up it is 20° colder.

−6 − 20 = −6 + (−20) = −26°

On the scale, subtracting 20 moves you 20 steps to the left of −6. You started below zero and went down, so the answer cannot be above zero.

Multiplying and dividing signed numbers

There is one rule, and it is the same for multiplying and for dividing (FAA General Handbook, Chapter 3, page 3-11):

  • Like signs give a plus. Plus times plus is plus. Minus times minus is plus.
  • Unlike signs give a minus. Plus times minus is minus. Minus times plus is minus.
SignsMultiplyingDividing
plus, plus3 × 6 = 186 ÷ 3 = 2
minus, plus−3 × 6 = −18−6 ÷ 3 = −2
minus, minus−3 × −6 = 18−6 ÷ −3 = 2
plus, minus3 × −6 = −186 ÷ −3 = −2

Work the size of the answer first, as if there were no signs. Then count the minus signs. One minus sign: the answer is minus. Two minus signs: the answer is plus.

Where a mechanic meets a minus sign

The FAA publishes a sheet of limits and data for each aircraft design. It is called the type certificate data sheet, or data sheet for short. The Cessna 172 is on data sheet number 3A12. You will learn to use the whole sheet in a later module. Here you need five things from it.

Weight. Weight is a measure of the pull of gravity on an object. In the shop it is measured in pounds, written lb. The pound is a unit: the named amount that a measurement is counted in.

Where zero is. The datum is an imaginary vertical plane from which all horizontal measurements are taken: picture a flat sheet standing upright across the airplane, with every distance along the airplane measured from it (FAA General Handbook, Chapter 6, page 6-2). It is the zero of the scale. The manufacturer decides where it is, and the data sheet prints the place. The firewall is the metal wall between the engine and the cabin. For N172BL the datum is the lower front face of the firewall (Type Certificate Data Sheet 3A12, page 15).

Two direction words. Forward means toward the nose of the airplane. Aft means toward the tail.

The arm. The arm of an item is the horizontal distance from the datum to that item. It is measured in inches, written in. An arm is a signed number. A plus sign means the item is aft of the datum. A minus sign means the item is forward of the datum (FAA General Handbook, Chapter 6, page 6-2). The data sheet prints the arm after the item, either inside round marks, as in (−14.0), or after the word "at", as in "at +95".

Two of the items on the data sheet are kinds of fuel. Usable fuel is the fuel the engine can burn. Unusable fuel is the fuel that stays in the tanks and the fuel pipes and cannot be burned when the tanks are considered to be empty (FAA General Handbook, Chapter 6, page 6-13).

N172BL is a model 172N: the letter after 172 names the model. (The N at the front of N172BL is not the model letter. It is part of the number painted on the airplane.) These are the arms the data sheet prints for the model 172N (Type Certificate Data Sheet 3A12, page 13; page 12; page 16):

ItemArm (in)Where that is
Oil−14forward of the datum: ahead of the firewall, where the engine is
Unusable fuel+46aft of the datum
Usable fuel+48aft of the datum, in the tanks in the wing (the surface that lifts the airplane)
Rear seats+73aft of the datum
Baggage+95aft of the datum

Figure 3 shows where each arm falls on the airplane. Only the oil has a minus arm.

Figure 3. The Cessna 172N from the side, with the datum and the arms the data sheet prints. The oil is forward of the datum, so its arm is minus. Everything else here is aft of the datum, so its arm is plus.

The moment. The moment of an item is the product of its weight multiplied by its arm (FAA General Handbook, Chapter 6, page 6-2). Pounds times inches gives pound-inches, written lb-in. (That handbook page writes the same unit with the inches first. This course writes moments in lb-in, as the FAA Weight and Balance Handbook does.)

moment = weight × arm

A moment is a force that tries to cause rotation (FAA Weight and Balance Handbook, Chapter 2, page 2-2). A force is a push or a pull, and rotation is turning. It says how hard a weight tries to tip the airplane about the datum: a heavier item, or one further from the datum, has a larger moment.

The same handbook page shows the idea on a lever: a bar resting on one point. In Figure 4 the datum is at that point, which the figure calls the fulcrum. Weight A is 100 lb, 50 in to the left of the datum, so its arm is −50. Weight B is 200 lb, 25 in to the right, so its arm is +25.

Figure 4. A lever with the datum at the point it rests on. Weight A, 100 lb, is at arm −50 in. Weight B, 200 lb, is at arm +25 in. FAA-H-8083-1B, Figure 2-1
  • Weight A: 100 × −50 = −5,000 lb-in (unlike signs, so minus)
  • Weight B: 200 × +25 = +5,000 lb-in (like signs, so plus)
  • Sum of the moments: −5,000 + 5,000 = 0

Figure 5 is the handbook's table for the same lever. A sum of zero means the two sides balance.

Figure 5. The moment table for the lever. The minus moment and the plus moment add to zero. FAA-H-8083-1B, Figure 2-2

The same table for N172BL. Four items are loaded on the airplane. The oil and unusable fuel weights are printed on the data sheet (Type Certificate Data Sheet 3A12, page 16). The usable fuel is 40 gallons of aviation gasoline (the gallon is the unit that fuel and oil are measured in), and the handbook gives 6 lb for each gallon (FAA General Handbook, Chapter 6, page 6-16): 40 × 6 = 240 lb. The baggage is the most the data sheet allows, 120 lb.

ItemWeight (lb)Arm (in)Moment (lb-in)
Full oil11.3−1411.3 × −14 = −158.2
Unusable fuel18+4618 × 46 = +828.0
Usable fuel240+48240 × 48 = +11,520.0
Baggage120+95120 × 95 = +11,400.0
Total389.3+23,589.8

Adding the moments one at a time: −158.2 + 828.0 = 669.8. Then 669.8 + 11,520.0 = 12,189.8. Then 12,189.8 + 11,400.0 = 23,589.8 lb-in.

Weight on, weight off. Putting an item on the airplane is a plus weight. Taking it off is a minus weight. With a plus or minus arm, that makes four cases (FAA General Handbook, Chapter 6, page 6-3):

WeightArmMoment
added (+)aft of the datum (+)plus
added (+)forward of the datum (−)minus
removed (−)aft of the datum (+)minus
removed (−)forward of the datum (−)plus

Now the problem from the top of the page. The oil drained is 11.3 lb removed, so its weight is −11.3. Its arm is −14. Like signs give a plus:

−11.3 × −14 = +158.2 lb-in

When the oil goes back in, the weight is a plus and the arm is still a minus: 11.3 × −14 = −158.2 lb-in. The two changes cancel, as they should.

Which step first

The total moment of the oil and the unusable fuel is written on one line like this:

(11.3 × −14) + (18 × 46)

Parentheses are the round marks ( ) that group numbers together. What is inside them is worked first (FAA General Handbook, Chapter 3, page 3-17). Here they tell you to work each multiplication and then add the two answers.

Now the same line with the parentheses left out:

11.3 × −14 + 18 × 46

The answer must not depend on someone remembering to write the parentheses. Adding, subtracting, multiplying and dividing are called operations. Arithmetic has an agreed order for working them, called the order of operations:

  1. Work inside parentheses first.
  2. Then multiply and divide, from left to right.
  3. Then add and subtract, from left to right.

The handbook's list has one more step, between steps 1 and 2 (FAA General Handbook, Chapter 3, page 3-18). Lesson 3 adds it.

With the parentheses, step 1 makes you multiply first. Without them, step 2 does the same job: multiply before you add. Either way the answer is the same. Figure 6 works the line without parentheses in the right order and in the wrong order.

Figure 6. One line with no parentheses, worked in the right order and in the wrong order. Multiply first, then add.
  • With parentheses (step 1): 11.3 × −14 = −158.2 and 18 × 46 = 828. Then −158.2 + 828 = +669.8 lb-in.
  • Without parentheses, in the right order (step 2, then step 3): 11.3 × −14 = −158.2 and 18 × 46 = 828. Then −158.2 + 828 = +669.8 lb-in. It is the same answer.
  • Without parentheses, in the wrong order, left to right as it comes: 11.3 × −14 = −158.2. Then −158.2 + 18 = −140.2. Then −140.2 × 46 = −6,449.2. That number means nothing.

In a moment table this is the reason you fill in every moment first and add the column last.

What one wrong sign does

The hazard. A minus sign is one small mark. It is easy to drop when you copy (−14.0) from the data sheet, and a calculator will not notice.

What it does. Work the N172BL table again with the oil arm copied as 14 instead of −14. The oil moment becomes +158.2, and the total becomes 158.2 + 828.0 + 11,520.0 + 11,400.0 = 23,906.2 lb-in. The right total is 23,589.8. The error is 316.4 lb-in, which is twice 158.2: once for the moment that should have been taken away, and once for the moment that was added by mistake. Every weight in that table is right and the total is still wrong. The weight paperwork of an airplane is built from totals like this one, and the next person who uses that paperwork cannot see the mistake in it.

How to prevent it.

  • Copy the sign with the number. Read the arm off the data sheet as "minus fourteen", not "fourteen".
  • Before you multiply, say where the item is: forward of the datum or aft of it. Forward is minus.
  • Check the sign of each moment against the rule before you add: like signs plus, unlike signs minus.
  • Multiply every line first. Add last.
Video transcript: Which side of zero (4 min 53 s)

This course has three parts, General, Airframe and Powerplant, and it starts with the mathematics a mechanic uses. Each lesson has a short video, a reading, practice and a quiz. This video uses an oil change to review basic arithmetic and numbers below zero. N172BL is in for an oil change, so the oil has been drained. The FAA's sheet for this airplane lists the oil at −14 inches.

Taking something off the airplane is also a minus. So this change has a minus times a minus. Is the answer a plus or a minus? Start with the whole numbers, which are 0, 1, 2, 3 and so on. Add these four numbers. The answer to an addition is the sum. Take one number from another. The answer to a subtraction is the difference.

Multiply 35 cartons by 18 filters. The answer to a multiplication is the product, 630 filters. Divide 218 bolts between 7 aircraft. The answer to a division is the quotient, 31 bolts each. One bolt is left over. That is the remainder. Now go below zero. A positive number is greater than zero. A negative number is less than zero.

On this scale, a line marked with numbers in order, zero is in the middle, negative numbers are to its left, and positive numbers to its right. A number that carries a plus or a minus sign is a signed number. You are in debt by 100 dollars, and you pay in 45. −100 + 45 = −55. To subtract a signed number, change the subtraction to an addition, change the sign of the second number, and add.

The temperature on the ground is −6 degrees, and higher up it is 20 degrees colder. −6 − 20 becomes −6 + (−20), which is −26 degrees. The FAA publishes a sheet of limits and data for each aircraft design. It is called the type certificate data sheet. The data sheet measures every distance along the airplane from one place, called the datum.

The datum is an imaginary vertical plane, and it is the zero of the scale. Picture a flat sheet standing upright across the airplane. On this airplane the datum is the lower front face of the firewall, the metal wall between the engine and the cabin. Forward means toward the nose. Aft means toward the tail. The arm of an item is the horizontal distance from the datum to that item, in inches.

Aft of the datum, the arm is a plus. Forward of the datum, the arm is a minus. The oil is at −14. The fuel that stays in the tanks and the fuel pipes and cannot be burned when the tanks are considered to be empty is the unusable fuel, at +46. The fuel the engine can burn is the usable fuel, at +48.

The rear seats are at +73 and the baggage is at +95. Multiply the weight of an item by its arm, and the product is its moment. Weight is in pounds and the arm is in inches, so a moment is in pound-inches. When you multiply two signed numbers, like signs give a plus. Unlike signs give a minus. Here is the table.

Full oil is 11.3 pounds at −14. Plus times minus is a minus, so its moment is −158.2. Unusable fuel, 18 pounds at +46, is +828.0. The usable fuel and the baggage are worked the same way. Add the moments last. The total is +23,589.8 pound-inches. Now the oil that was drained. It was taken off, so its weight is −11.3.

Its arm is −14. Like signs give a plus. −11.3 × −14 = +158.2 pound-inches. Write the moments of the oil and the unusable fuel on one line. The round marks are parentheses. Arithmetic also has an agreed order, called the order of operations. Work inside parentheses first, then multiply and divide from left to right, then add and subtract from left to right.

Without the parentheses, you still multiply before you add, which gives +669.8. Work it left to right as it comes, and it gives −6,449.2. See what one dropped minus sign does. Copy the oil arm as 14 instead of −14, and the total becomes 23,906.2. That is 316.4 pound-inches too many, twice the moment of the oil. So copy the sign with the number, and say forward or aft before you multiply.

Now you try it. Put the five arms on the number line. Then fill in a moment table.