The reading from the lesson above, as plain text. The video, the practice and the quiz are in the lesson itself.
Airplanes that run out of gas crash. How do you figure out how many gallons the tank holds?
This lesson shows how to find volume, how much a space holds. The example is line 8 of the work order on N172BL: how much one of its fuel tanks, the space for bags behind the seats and the engine hold.
By the end of this lesson you will be able to:
Line 8 of the work order on N172BL asks how much three things hold: one of the containers the fuel is carried in, the space for bags behind the seats, and the engine. On an airplane the container the fuel is carried in is called a fuel tank. The space where bags are carried is called the baggage compartment. The data sheet says each of the two fuel tanks in the wings holds 21.5 gallons (Type Certificate Data Sheet 3A12, page 13).
A tank is a metal box. How big a box is 21.5 gallons, in inches? And the size of an engine is not given in gallons at all. It is given by the space its pistons move through. This lesson shows how to find the space inside a box, a can and a tank, and how to change that space into gallons.
TRAINING DATA: the work order is made up. The 21.5 gallons is from the data sheet.
Volume is the amount of space within a solid. A solid is a shape that has length, width and height: a box, a can, a ball (FAA General Handbook, Chapter 3, page 3-20). Lesson 4 used the word for the space inside an engine cylinder. This lesson shows how to work it out.
Area is counted in squares. Volume is counted in blocks. A cubic inch (cu in) is the space inside a block that is 1 inch long, 1 inch wide and 1 inch high. A cubic foot (cu ft) is the space inside a block that is 1 foot on each side. Units like these are called cubic units. Small spaces are given in cubic inches and larger spaces in cubic feet.
A rectangular solid is a solid with six rectangular sides: a box. Its volume is the number of cubic units that fit inside it.
volume = length × width × height
Figure 1 shows a rectangular solid 3 ft long, 2 ft wide and 2 ft high. Its volume is 3 ft × 2 ft × 2 ft = 12 cu ft. Count the blocks in the figure: there are 12. Feet times feet times feet gives cubic feet (FAA General Handbook, Chapter 3, page 3-21).
A cube is a rectangular solid whose six sides are all squares, so its length, width and height are the same (Figure 2). Its volume is side × side × side. The handbook's carton is 3 ft on each side: 3 × 3 × 3 = 27 cu ft (FAA General Handbook, Chapter 3, page 3-21).
All three sides must be in the same unit before you multiply. The handbook's baggage compartment is 5 ft 6 in long, 3 ft 4 in wide and 2 ft 3 in high (Figure 3). Change each side to feet: divide the inches by 12 and add them to the feet.
Volume = 5.5 × 3.3333 × 2.25 = 41.25 cu ft, to two decimal places. Six inches is 0.5 ft, not 0.6 ft.
The data sheet gives no dimensions for N172BL's baggage compartment, so you learn the method on the handbook's. In the shop you would measure the three sides of the compartment and work them the same way.
The handbook's page writes the width as 3.33 ft. Multiply 5.5 × 3.33 × 2.25 and you get 41.21, not the 41.25 the page prints (FAA General Handbook, Chapter 3, page 3-21). The printed answer is the right one. It comes from carrying the extra digits and rounding once, at the end, as Lesson 2 showed.
A cylinder is a solid in the shape of a can, a length of pipe or a barrel. Its two ends are identical circles (Figure 4). Lesson 4 used the word cylinder for the part of an engine that a piston moves in. That part is named for its shape. Both meanings are used from here on.
The volume of a cylinder is the area of the circle on its end multiplied by its height. The height of a cylinder is the distance between its two ends. The area of a circle is π × radius × radius (Lesson 7), so:
volume = π × r² × h
In the formula, r is the radius of the circle on the end and h is the height of the cylinder. Use 3.1416 for π (FAA General Handbook, Chapter 3, page 3-21).
Two measurements give the size of an engine cylinder (Figure 5). The bore is the inside diameter of the cylinder. The stroke is the length the piston travels inside the cylinder (FAA General Handbook, Chapter 3, page 3-22). The piston travels between two positions. Top center is the piston's highest position in the cylinder. Bottom center is its lowest. The FAA Powerplant Handbook calls them top dead center (TDC) and bottom dead center (BDC) (FAA Powerplant Handbook, Chapter 1, page 1-25).
As the piston moves from bottom center to top center it sweeps through a space shaped like a can: a cylinder as wide as the bore and as high as the stroke. The pistons turn a shaft (a round bar that turns) called the crankshaft, which changes their up-and-down motion into turning motion. Piston displacement is the sum of the volumes swept by all of the pistons of a reciprocating engine as they move in one revolution (one full turn) of the crankshaft (FAA General Handbook, Chapter 3, page 3-21). It is how the size of an engine is stated.
For one cylinder, the displacement is the area of the bore multiplied by the stroke. For the whole engine, multiply by the number of cylinders (FAA Powerplant Handbook, Chapter 1, page 1-28).
piston displacement = π × (bore ÷ 2)² × stroke × number of cylinders
The handbook works an engine with a 5.5 in bore, a 5.4 in stroke and eight cylinders. The handbook's engine is not N172BL's engine.
The most common mistake is to use the bore as the radius. The bore is a diameter. Halve it first.
The handbook rounds the area to 23.758 in the middle of the work and prints 128.29 and 1,026.32 (FAA General Handbook, Chapter 3, page 3-22). Carrying every digit gives 128.29509 and 1,026.36072, which are 128.30 and 1,026.36 to two decimal places. Both are accepted in this lesson where you type an answer to two decimal places. Carrying the digits and rounding once, at the end, is the better habit: each early rounding throws a little away.
The FAA Powerplant Handbook works a 14-cylinder engine with a 5.5 in bore and a 5.5 in stroke the same way. One cylinder is 23.75835 × 5.5 = 130.670925 cu in. Fourteen cylinders are 14 × 130.670925 = 1,829.39295 cu in, which is 1,829 cu in to the nearest whole number (FAA Powerplant Handbook, Chapter 1, page 1-29).
Lesson 4 gave the compression ratio as a ratio of two volumes. Now you can build those volumes. Figure 6 names them. The displacement volume is the volume the piston sweeps in one cylinder between bottom center and top center. The clearance volume is the space left above the piston at top center. It includes the space in the cylinder head, the closed top end of the cylinder, that the piston never reaches. The total volume is the two together: the whole space above the piston at bottom center.
total volume = displacement volume + clearance volume
With a displacement volume of 120 cu in and a clearance volume of 20 cu in, the total volume is 120 + 20 = 140 cu in. The compression ratio compares the total volume with the clearance volume: 140 to 20. Divide both numbers by 20 and the ratio reduces to 7:1 (FAA Powerplant Handbook, Chapter 1, page 1-29; Figure 1-38, page 1-30).
Read the figure from the right-hand cylinder. The piston is at top center, and the yellow space above it is the clearance volume: a thin band above the piston and the space in the cylinder head above that. The dashed line beside the "Clearance volume" tag runs across to the top of that space. The line under tag 1 is level with the top of the piston at top center, and the line under tag 7 is level with the top of the piston at bottom center. The "Displacement volume" arrow runs between those two lines. The "Total volume" arrow runs from the dashed line to the line under 7. The figure marks the total volume as 7 parts. The clearance volume is 1 of them and the displacement volume is the other 6: 7 to 1.
A mechanic may know the volume of a tank in cubic inches and need it in gallons. The handbook's table of units gives the two factors you need; Figure 7 shows those rows (FAA General Handbook, Chapter 3, Figure 3-23, page 3-22).
A cubic foot is a block 12 in long, 12 in wide and 12 in high: 12 × 12 × 12 = 1,728 cu in. To change cubic feet to cubic inches, multiply by 1,728: 2 cu ft = 2 × 1,728 = 3,456 cu in. To change cubic inches to cubic feet, divide by 1,728.
One of N172BL's fuel tanks holds 21.5 gal. In cubic inches that is 21.5 × 231 = 4,966.5 cu in. In cubic feet it is 4,966.5 ÷ 1,728 = 2.87 cu ft. The engine oil, 1.5 gal (Type Certificate Data Sheet 3A12, page 13), is 1.5 × 231 = 346.5 cu in.
The same table prints 1 cubic foot as 7.5 gallons. That figure is rounded: 1,728 ÷ 231 = 7.48. Go through cubic inches, with 231 and 1,728, and the answer is exact.
A real tank is seldom a plain box. Split it into shapes you know, find the volume of each, and add them. Figure 8 is a tank drawn as a box with a wedge on top. A wedge is a solid whose two ends are identical triangles, like a box cut in half from corner to corner. Wedge is a plain word. This definition is plain mathematics; it is not from an FAA page.
The handbook prints no formula for a wedge. Build one from two rules that are printed. The cylinder rule was: the area of the circle on the end, multiplied by the distance between the two ends (FAA Powerplant Handbook, Chapter 1, page 1-28; that page calls the end the base, and the distance between the ends the height). The same rule holds for a wedge. The end of the wedge is the triangle on its front. Lesson 7 gave the area of a triangle as 1/2 × base × height (FAA General Handbook, Chapter 3, page 3-18). The base of this triangle is the length of the tank, so its area is 1/2 × length × height. The distance between the two ends of the wedge is the width of the tank. This step is plain mathematics; no FAA page prints it as a wedge formula.
volume of a wedge = (1/2 × length × height) × width
The dimensions in Figure 8 are made up so that the drawing holds the data sheet's 21.5 gal. It is not the real tank's shape.
That agrees with the data sheet.
The handbook gives two more solids. You need to know them by sight. This lesson does not ask you to work them.
A sphere is a solid in the shape of a ball (Figure 9). Its volume is 4/3 × π × r³, where r is the radius of the ball (FAA General Handbook, Chapter 3, page 3-22; the formula is at the top of page 3-23).
A cone is a solid with a circle at one end and with sides that taper to a point at the other (Figure 10). The handbook calls the circle the base of the cone. Its volume is 1/3 × π × r² × h, where r is the radius of the base and h is the height (FAA General Handbook, Chapter 3, page 3-23).
Volume is not the only size a solid has. The surface area of a solid is the sum of the areas of its faces, the flat sides that make up its outside (FAA General Handbook, Chapter 3, page 3-23). It is given in square units, not cubic units. The handbook puts the difference this way: surface area is the amount of sheet metal needed to build a rectangular fuel tank, and volume is the amount of fuel the tank can contain (FAA General Handbook, Chapter 3, page 3-24). A cube 8 in on a side has six faces of 8 × 8 = 64 sq in each. Its surface area is 6 × 64 = 384 sq in.
Figure 11 collects the formulas for volume and surface area (FAA General Handbook, Chapter 3, page 3-26). Its first row should say "Rectangular solid".
This video covers volume, how much something holds. By the end of the lesson you will be able to find the volume of a box, a tank and an engine. Line 8 of the work order on N172BL asks how much three things hold: a fuel tank, the baggage compartment, and the engine. The container the fuel is carried in is called a fuel tank.
The space where bags are carried is called the baggage compartment. The data sheet says each of the two fuel tanks in the wings holds 21.5 gallons. A tank is a metal box. How big a box is 21.5 gallons, in inches? Volume is the amount of space within a solid. A solid is a shape that has length, width and height: a box, a can, a ball.
Area is counted in squares. Volume is counted in blocks. A cubic inch is the space inside a block that is 1 inch long, 1 inch wide and 1 inch high. A cubic foot is the space inside a block that is 1 foot on each side. A rectangular solid is a solid with six rectangular sides: a box. Its volume is length times width times height.
The FAA General Handbook's box is 3 ft long, 2 ft wide and 2 ft high. 3 × 2 × 2 = 12 cu ft. All three sides must be in the same unit before you multiply. The handbook's baggage compartment is 5 ft 6 in long, 3 ft 4 in wide and 2 ft 3 in high. Change each side to feet, then multiply: the volume is 41.25 cu ft.
A cylinder is a solid in the shape of a can, a length of pipe or a barrel. The volume of a cylinder is the area of the circle on its end multiplied by its height. The area of a circle is π × radius × radius, from Lesson 7. So volume = π × r² × h. Two measurements give the size of an engine cylinder.
The bore is the inside diameter of the cylinder. The stroke is the length the piston travels inside the cylinder. Top center is the piston's highest position in the cylinder. Bottom center is its lowest. As the piston moves from bottom center to top center it sweeps through a space shaped like a can. The pistons turn a shaft called the crankshaft.
Piston displacement is the sum of the volumes swept by all of the pistons as they move in one full turn of the crankshaft. For one cylinder, displacement = π × r² × stroke, where r is half the bore. For the whole engine, multiply by the number of cylinders. The handbook works an engine with a 5.5 in bore, a 5.4 in stroke and eight cylinders.
The handbook's engine is not N172BL's engine. Halve the bore first: the radius is 2.75 inches. Square the radius: 7.5625. Multiply by π, 3.1416: 23.75835 sq in. That is the area of the bore. Multiply the area by the stroke: 128.3 cu in for one cylinder. Multiply by eight cylinders: about 1,026 cu in. The most common mistake is to use the bore as the radius.
The bore is a diameter. A real tank is seldom a plain box. Split it into shapes you know, find the volume of each, and add them. This tank is drawn as a box with a wedge on top. A wedge is a solid whose two ends are identical triangles, like a box cut in half from corner to corner.
The dimensions are made up for training. The box: 35 × 21 × 6 = 4,410 cu in. The wedge is half of a box: ½ × 35 × 1.5 × 21 = 551.25 cu in. Together: 4,961.25 cu in. Now change cubic inches into gallons. The handbook's table gives 1 gallon = 231 cu in. Divide by 231: 21.477, which rounds to 21.5 gal.
That agrees with the data sheet. The surface area of a solid is the sum of the areas of its faces, the flat sides that make up its outside. The handbook puts the difference this way: surface area is the amount of sheet metal needed to build a rectangular fuel tank, and volume is the amount of fuel the tank can contain.
A cube 8 in on a side has six faces of 64 sq in each. 6 × 64 = 384 sq in. Volume is what it holds. Surface area is what it takes to build it. Now work the practice below the video: an engine's displacement, a tank in gallons, and feet and inches.