The reading from the lesson above, as plain text. The video, the practice and the quiz are in the lesson itself.
The book says 100 to 140 inch-pounds, but the wrench only reaches the nut with an extension. What do you set the wrench to?
This lesson shows how to use a formula, a line of letters that shows how to work one quantity out from others. The example is line 5 of the work order on N172BL: tightening one nut with an added piece on the wrench.
By the end of this lesson you will be able to:
Line 5 of the work order on N172BL is about one nut. It must be tightened to a measured amount, and the wrench that measures the tightening cannot reach it. You add a piece to the end of the wrench to reach the nut. The added piece makes the wrench longer, and a longer wrench tightens the nut harder than the wrench shows.
So what must the wrench show for the nut to get the tightening the job calls for? The FAA General Handbook answers with a row of letters: Tw = (Te × A) ÷ B. This lesson teaches you to read a line like that, put your numbers into it, turn it around to find a different letter, and work it in the right order. Worked in the wrong order, the same line gives a number that looks right and is wrong.
TRAINING DATA: the work order and the lengths of the wrench are made up. The table and the formulas are from FAA documents.
Some rules work for any numbers. Such a rule is written once, with letters in place of the numbers, and used on every job. Three words go with this:
Algebra is "the branch of mathematics that uses letters or symbols to represent variables in formulas and equations" (FAA General Handbook, Chapter 3, "Algebra").
The handbook's example is d = v × t, where distance = velocity × time. Velocity here means speed. The variables are d, v and t.
To use a formula you substitute: you put the known numbers in place of the letters. An airplane flies at 120 miles per hour for 2 hours. How far does it go?
| Step | Working |
|---|---|
| Write the formula | d = v × t |
| Substitute | d = 120 × 2 |
| Work it | d = 240 miles |
One more thing to know when you read a formula: a number written against a letter is multiplied by it. 3N means 3 × N.
To solve an equation is to find the number that the letter stands for. The handbook gives one rule for it: you may add, subtract, multiply or divide, as long as you "do the same to both sides of the equals sign," until the letter is alone on one side (FAA General Handbook, Chapter 3, "Algebraic Rules").
Think of the equals sign as the middle of a balance (Figure 1). The two sides weigh the same. Take the same amount off both sides and it stays level.
To get the letter alone, undo what has been done to it. Division undoes multiplication, and subtraction undoes addition. These are the handbook's four examples:
| Equation | Done to N | Do to both sides | N = |
|---|---|---|---|
| 3N = 21 | multiplied by 3 | divide by 3 | 7 |
| N + 17 = 59 | 17 added | subtract 17 | 42 |
| N − 22 = 100 | 22 subtracted | add 22 | 122 |
| N/5 = 50 | divided by 5 | multiply by 5 | 250 |
Check every answer by putting it back in the equation: 3 × 7 = 21, so N = 7 is right.
The same rule turns a formula around, so that it finds a different letter. This is called rearranging the formula.
An airplane must go 240 miles at 120 miles per hour. How long does it take? The formula d = v × t has t multiplied by v. Divide both sides by v, and t is alone:
| Step | Working |
|---|---|
| Write the formula | d = v × t |
| Divide both sides by v | d ÷ v = t |
| Write it with t on the left | t = d ÷ v |
| Substitute | t = 240 ÷ 120 |
| Work it | t = 2 hours |
Nothing new was learned about airplanes. One formula now answers three questions: how far (d = v × t), how long (t = d ÷ v) and how fast (v = d ÷ t).
A force is a push or a pull. In this course a force is measured in pounds. (This is a working definition; the physics module teaches force in full. The handbook's own definition is in its glossary: FAA General Handbook, Glossary, "Force".)
Torque is "the tendency of a force to cause or change rotational motion of a body" (FAA General Handbook, Glossary, "Torque"). In plain words, torque is a turning force. When you pull on the handle of a wrench, the pull is a force, and what the nut feels is torque.
The right torque matters. The handbook says that proper torque on every nut and bolt lets the structure carry the load it was designed for (FAA General Handbook, Chapter 7, "Fastener Torque"). A torque wrench is a wrench that shows, or limits, the torque it is putting on a nut or bolt. (A working definition; the hand tools module teaches the types.) The drive is the square end of the wrench that turns the nut, through a socket, the cup-shaped tool that fits over the nut.
Figure 2 prints the basic formula at the top: F × L = T. Written the way the other formulas in this lesson are written, it is T = F × L:
The inch-pound is the unit of torque when the force is in pounds and the length is in inches. It is written in-lb. The torque table you are about to use is in inch-pounds.
A hand that pulls with 20 pounds on a wrench 10 inches long puts T = 20 × 10 = 200 inch-pounds on the nut.
You have multiplied pounds by inches before: a moment is a weight times its distance from the datum. This course writes a moment in pound-inches (lb-in) and a torque in inch-pounds (in-lb), so that the two are never mixed up.
Now line 5 of the work order can be read in full: "Torque nut. Extension needed to reach."
A drive end extension is a piece added to the drive end of a torque wrench. This lesson calls it an extension for short. It lets the wrench reach a nut that the wrench alone cannot get onto, and it makes the wrench longer. An extension is in line when it points straight out from the end of the wrench, as the extension in Figure 2 is drawn. This lesson works only with an extension that is in line.
A longer wrench puts more torque on the nut than the wrench shows. So the handbook makes a rule: "The use of a drive end extension on any type of torque wrench makes the use of the formula mandatory" (FAA General Handbook, Chapter 7, "Torque Wrenches"). AC 43.13 says the same: when an added piece changes the length of the wrench, the wrench setting "must be adjusted accordingly" (AC 43.13, par. 7-40h).
The formula is at the bottom of the same handbook figure (Figure 3; the whole figure: FAA General Handbook, Figure 7-33):
Tw = Te × A/B
Both lengths are measured from the center of the hand, and the hand must pull at that same point.
First, the torque wanted. The manufacturer's manual is the maintenance book written by the company that built the airplane. Where it gives a torque for the nut, that is the value to use. AC 43.13 says its table is for use "when specific torque is not supplied by the manufacturer" (AC 43.13, par. 7-40i), and the handbook says the same of its own table (FAA General Handbook, Chapter 7, "Torque Tables"). On this training job no manual value is given, so the table applies. The table is entered by thread size. The nut on this job goes on a bolt with a 5/16-24 thread: 5/16 inch across, with 24 threads to the inch (the hardware module teaches thread sizes). The first column of numbers is headed "Tension type nuts," and for this training job that is the kind of nut on the bolt. The 5/16-24 row gives 100-140 inch-pounds in that column (AC 43.13, Table 7-1). Open the page and find the row: every value in the table is in inch-pounds. You choose 120, the middle of the range.
The wrench is 10 inches long and the extension adds 2 inches, in line.
| Step | Working |
|---|---|
| Find B | B = 10 + 2 = 12 in |
| Write the formula | Tw = (Te × A) ÷ B |
| Substitute | Tw = (120 × 10) ÷ 12 |
| Multiply | Tw = 1,200 ÷ 12 |
| Divide | Tw = 100 in-lb |
Set the wrench to 100 inch-pounds and the nut gets 120.
Turn the formula around to find Te. Te has been multiplied by A and divided by B. Undo both: multiply both sides by B, then divide both sides by A.
| Step | Working |
|---|---|
| Write the formula | Tw = (Te × A) ÷ B |
| Multiply both sides by B | Tw × B = Te × A |
| Divide both sides by A | (Tw × B) ÷ A = Te |
| Write it with Te on the left | Te = (Tw × B) ÷ A |
| Substitute | Te = (120 × 12) ÷ 10 |
| Multiply | Te = 1,440 ÷ 10 |
| Divide | Te = 144 in-lb |
The wrench would show 120 and the nut would get 144 inch-pounds, which is over the top of the 100-140 range.
A formula with more than one operation must be worked in a set order. You met the order of operations in earlier lessons. The handbook's memory word for it is PEMDAS (FAA General Handbook, Chapter 3, "Order of Operation"; the word is at the foot of page 3-17, and its sentence runs on to page 3-18):
The letters make six words, but there are four steps. The list printed on page 3-18 numbers six steps; the sentence above that list says to multiply and divide "in one sweep from left to right, not separately," and that sentence is the rule.
The hazard. A basic calculator, or a pencil, will work a formula in whatever order the numbers are keyed in. The wrong order still gives an answer, and nothing about the answer says it is wrong.
How it hurts. Take line 5. B is the bottom of a fraction, so the sum 10 + 2 is worked first. Key the numbers in from left to right without it, and you divide before you add (Figure 4):
A wrench set to 122 inch-pounds with this extension puts 146.4 inch-pounds on the nut: over the top of the range, on a nut the record will say was torqued correctly.
Temperature gives a second example. Celsius (°C) and Fahrenheit (°F) are the two temperature scales that shop thermometers use: water freezes at 0 °C, which is 32 °F. (A working definition; the next lesson teaches the scales.) The handbook's formula is Degrees Fahrenheit = (1.8 × Degrees Celsius) + 32 (FAA General Handbook, Chapter 5, "Temperature"). The parentheses say: multiply first, then add.
| At 20 °C | Working | Result |
|---|---|---|
| Right order | (1.8 × 20) + 32 = 36 + 32 | 68 °F |
| Wrong order: added first | 1.8 × (20 + 32) = 1.8 × 52 | 93.6 °F |
Both numbers could be a day's temperature. Only one is right. This mistake is easy enough to make that the handbook's own formula sheet prints the parentheses in the wrong place; do not use that line (FAA General Handbook, Figure 3-23).
How to prevent it.
The handbook works one long equation through all four steps (FAA General Handbook, Chapter 3, "Order of Operation"). It uses powers, a square root and brackets from lesson 3:
N = (62 − 54)² + 6² − 4 + 3 × [8 + (10 ÷ 2)] + √25 + (42 × 2) ÷ 4 + 3/4
| Step | The equation becomes |
|---|---|
| 1. Parentheses and brackets | (8)² + 6² − 4 + 3 × [13] + √25 + 84 ÷ 4 + 3/4 |
| 2. Powers and roots | 64 + 36 − 4 + 3 × 13 + 5 + 84 ÷ 4 + 3/4 |
| 3. Multiply and divide | 64 + 36 − 4 + 39 + 5 + 21 + 3/4 |
| 4. Add and subtract | N = 161 3/4 |
This video starts with one nut. By the end of the lesson you will be able to use a formula, turn it around and work the steps in order. Line 5 of the work order on N172BL is about one nut. The wrench that measures the tightening cannot reach it, so you add a piece to the end of the wrench.
The added piece makes the wrench longer, and a longer wrench tightens the nut harder than the wrench shows. So what must the wrench show? The FAA General Handbook answers with a row of letters: Tw = (Te × A) ÷ B. This video shows you how to use a line like that. An equation is a statement, with an equals sign, that two things are equal.
A formula is an equation that shows how to work one quantity out from others. The handbook's example is d = v × t: distance = velocity × time. Velocity here means speed. To use a formula you substitute: you put the known numbers in place of the letters. An airplane flies at 120 miles per hour for 2 hours.
d = 120 × 2 = 240 miles. To solve an equation is to find the number that the letter stands for. The handbook gives one rule for it: do the same to both sides of the equals sign. Take 3N = 21. 3N means 3 × N. Divide both sides by 3, and N = 7. The same rule turns a formula around.
In d = v × t, divide both sides by v, and t = d ÷ v. A force is a push or a pull. Torque is a turning force. The handbook's figure prints the formula at the top: F × L = T. The inch-pound is the unit of torque when the force is in pounds and the length is in inches.
A torque wrench is a wrench that shows, or limits, the torque it is putting on a nut or bolt. The drive is the square end of the wrench that turns the nut, through a socket. A drive end extension is a piece added to the drive end of a torque wrench. This one is in line: it points straight out from the end of the wrench.
So the handbook makes a rule: the use of a drive end extension on any type of torque wrench makes the use of the formula mandatory. In that formula, Te is the torque wanted on the nut. Tw is what the torque wrench must show. A is the length of the wrench alone. B is the length of the wrench plus the extension.
On this training job no manual value is given, so the table in AC 43.13 applies. The row for this bolt's thread size, 5/16-24, gives 100-140 inch-pounds. You choose 120, the middle of the range. The wrench is 10 inches long, and the extension adds 2 inches, in line. So A = 10, and B = 10 + 2 = 12.
Now substitute. Tw = (120 × 10) ÷ 12. 120 × 10 = 1,200. 1,200 ÷ 12 = 100. Set the wrench to 100 inch-pounds, and the nut gets 120. What if the wrench were set to 120 anyway? Turn the formula around: Te = (Tw × B) ÷ A. The nut would get 144 inch-pounds, which is over the top of the range.
A formula must be worked in a set order. The handbook's memory word for it is PEMDAS. Parentheses first. Then exponents: powers and roots. Then multiplication and division, together, from left to right. Then addition and subtraction, together, from left to right. B is the bottom of a fraction, so the sum 10 + 2 is worked first. Key the numbers in from left to right, and you divide before you add.
120 × 10 ÷ 10 + 2 = 122. That number looks right, and it is wrong. Celsius and Fahrenheit are the two temperature scales that shop thermometers use. The handbook's formula is Degrees Fahrenheit = (1.8 × Degrees Celsius) + 32. At 20 °C, multiply first: 1.8 × 20 = 36, and 36 + 32 = 68 °F. Add first, and you get 93.6 °F.
Only one is right. To prevent it, write the formula down before you put numbers in. Work one step on each line, in PEMDAS order. Then ask whether the answer makes sense. With an extension, the wrench must show less than the torque wanted, and 122 is more than 120. Now it is your turn. In the practice below this video, put the steps of a formula in order, then work out the wrench setting for a new extension.